Composite mesh for walkways and blind areas: reinforcement that does not rust

Garden paths, paving around the house and entrance platforms work in the most difficult conditions for concrete: temperature drops, snow melting, rains, and in winter — deicing reagents. Without reinforcement, a thin concrete slab quickly cracks and crumbles along the edges. Correctly selected mesh for tracks takes on tensile stresses and transforms brittle concrete into a sturdy reinforced structure that keeps shape season after season.

Why choose composite mesh for walkways and blind areas

Traditionally, the paths are reinforced with a metal welded mesh or a netting mesh. The problem is that in the path and blind area, the metal is almost always in a zone of variable humidity — which means it rusts. Rust increases in volume, tears the protective layer of concrete, and red spots and cracks appear on the surface. Composite fiberglass mesh ETHYZ is devoid of this drawback in principle.

• Does not rust or corrode — glass composite is inert to water, salts and reagents, so the blind area does not "bloom" red and is not destroyed from the inside.
• Lighter than metal — a roll of mesh is carried and laid by one person, there is no need for a crane and loaders.
• Dielectric — does not conduct current and does not create cold bridges in the structure.
• Flex. — is rolled into a roll, easily rolled along a curved track and cut locally with scissors or a grinder.
• High fracture strength and durability — serves the entire lifespan of a concrete slab.

ETIZ composite reinforcement mesh complies with GOST 31938-2012 for composite polymer reinforcement and mesh, that is, it is not an artisanal material, but a standardized replacement of metal. You can pick up the canvas in eTHYZ Composite Mesh Catalogue.

What cell is needed for the path and blind area

For pedestrian garden paths, blind areas and light sites, the cell is optimal 100*100mm: it gives a sufficient frequency of reinforcement at a reasonable consumption of material and fits comfortably in a thin layer of concrete. For heavier loads, larger diameter rods are taken, for auxiliary work — a larger cell.

SSC reinforcement grid is available in SSC-2, SSC-3, SSC-5 and SSC-6 grades, in black or green, in convenient formats of rolls and cards (0.5×2, 0.5×15, 1×2, 1×15, 2×30, 1.35×50 m and others). For tracks, a roll is most often taken: it is quickly rolled out along the entire length of the track without joints and overlaps.

How to reinforce the track with composite mesh: step by step

1. Prepare the base. Remove the vegetation layer, fill and tamp the sand-gravel cushion, if necessary, install the formwork along the edges of the track.
2. Roll out the net. Unfold the roll along the track. The flexible blade easily repeats turns; cut the excess with scissors on metal or with a grinder right on the spot.
3. Lift the mesh into the concrete body. Lay the canvas on the retainers ("chair" stands) so that it is approximately in the middle of the plate thickness, and does not lie at the bottom. Only then does the mesh really stretch.
4. Mate the blades overlapping. Stack adjacent cards or turns with an overlap of several cells and tie with plastic clamps or knitting wire. Composite can not be boiled — only knitting.
5. Fill and compact the concrete. Lay the mixture, vibrate or pierce, level and cover with a film for the time of strength gain.

The whole process does not require special equipment: a light grid is convenient to carry, and cutting in place saves the time of the team. This is the main practical advantage of the composite for private construction.

Masonry mesh — for seams, not for tracks

Do not confuse the reinforcement grid for planes with the masonry grid. Masonry fiberglass (basalt) mesh ETIZ is narrow tapes with a width of 0.36, 0.5 and 1 m in rolls of 50 m each with a tensile strength of up to 50/50 kN/m. It is laid in horizontal joints of brick, aerated concrete and foam masonry. For paths, blind areas and screeds, it is a wide SSC reinforcement grid with a cell of 100×100 mm that is needed — it reinforces the entire plane. Both types of canvas are assembled in a single composite mesh section.

Final

Composite mesh for walkways and blind areas is a durable replacement of metal where concrete is constantly encountered with water and reagents. The 100×100 mm cell, light roll, cut with scissors and full corrosion resistance make it the best choice for landscaping the site. ETIZ specialists will help you choose the exact brand, format and volume for your project upon request.

FAQs

Which composite mesh cell is needed for the garden path?

For pedestrian garden paths and blind areas, a reinforcement grid with a cell of 100×100 mm and a rod of Ø2–3 mm is optimal. It gives a sufficient frequency of reinforcement at an economical material consumption and fits well in a thin layer of concrete. For entrance zones, a Ø3 mm rod is taken for the car, and a 200×200 mm cell is suitable for large areas. The exact brand for the load is selected by ETIZ specialists upon request.

Will the composite mesh rust in the blind area?

No. Ethyz fiberglass reinforcement mesh does not rust or corrode in principle, since the composite is inert to water, salts and deicing agents. That is why it is especially advantageous in blind areas and walkways, where the metal mesh rusts over time, tears the concrete from the inside and leaves red undercurrents on the surface.

Is it possible to cut and connect the composite mesh on site?

Yes. The mesh is easy to cut right on the spot with scissors on metal or grinder — special tools are not needed. Adjacent webs are laid overlapping on several cells and tied with plastic clamps or binding wire. It is important to remember: the composite can not be cooked, the connection is made only by viscous.

Why is composite mesh better than metal welded mesh for walkways?

It does not rust, is much lighter, is dielectric and does not create cold bridges. A light roll is carried and laid by one person without a crane, and a flexible canvas repeats the turns of the track. At the same time, the mesh has a high tensile strength, is durable and complies with GOST 31938-2012 as a standardized replacement of metal.

In what format is the lane net supplied and how much does it cost?

SSK reinforcement grid is available in rolls and cards of different sizes — 0.5×2, 1 × 2, 2 × 30, 1.35×50 m and others, black or green, SSK-2, SSK-3, SSK-5, SSK-6. For paths, a roll is more convenient: it is rolled out along the entire length without unnecessary joints. The cost depends on the brand, cell and volume and is calculated on request.